Furnace in energy conservation and emissions reduction facto
1、 Rectifier transformer
Guarantee transformer supplier know the load type of transformer, the load of medium power supply transformer is a rectifier load, which should kept the main efficiency shown on the transformer nameplate. Generally speaking, we use K coefficient to measure the loss caused by the transformer harmonics. The K coefficient of 6 pulses rectifier transformer is K-9, while K coefficient of 12 pulses rectifier transformer is K-4, The efficiency of rectifier transformer is entirely possible to reach 99% in common condition, Normally, we choose 98.5% as the minimum value.
2、 Incoming lines of the transformer
The energy loss, which is caused by connecting lines between secondaly side of transformer and medium power supply, is very small. When considering regular current density of bus bar and cable, the energy lose is 6/V% per meter. Here V is the voltage of incoming line of medium frequency power supply. For example, when the primary voltage of the transformer is 10kV, and the secondaly side is 575V, we had better plant transformer and power supply as closely as possible. Shorten distance between transformer and power supply at maximum degree contributes to reduce the energy loss on the side of power supply.
For example, the secondaly side voltage of transformer is 575V,and the distance is 20 meters, then there will be 0.2% energy loss.
3、 Medium frequency power supply
The main loss of the medium frequency power supply depends on the type and frequency of inverter.
The following is an energy loss comparision of main components when F<700Hz.
|
SCR |
IGBT |
|
Series |
Parallel |
Series |
Parallel |
DC Choke |
1.1% |
1.9% |
1.1% |
1.9% |
didt chokes |
0.9% |
0.45% |
0% |
0% |
Devices |
0.8% |
0.58% |
1.6% |
1.2% |
(Rel#) |
(2) |
(1) |
(4) |
(2) |
Total |
2.8% |
2.9% |
2.7% |
3.1% |
The comparision above shows us there is a little difference between main components.When device works at low frequency, the loss of IGBT is higher than SCR, when the same current is needed, the number of IGBT is more than SCR. But with frequency increasing, the rated capacity of SCR reduced. Normally IGBT has more advantages when the frequency is above 2kHz.
4、Resonance capacitor
Normally, we consider ~0.15W/100kVAr as the loss of resonance capacitor. Whether it is a series resonance or a parallel resonance circuit, the resonance capacitors are used for compensating power factor caused by coil lag. So for the energy loss, there is no much difference between the two kinds of circuits.
However, using capacitors with high capacity in practice has more advantages of energy-saving. It can reduce the dimension of cabinet, number of capacitors and cables connected capacitors and busbar, so lower energy loss can be achieved.
5、Output busbar
Considering the regular current density,typical energy loss can be calculated by the following datas ;
For water cooled busbur, the loss is 0.1% per meter.
For air cooling busbar, the loss is 0.065% per meter.
If only take the energy loss into consideration, it is very important to reduce the length of water cooled leads and the distance between inverter output and furnace, Air cooling busbar has higher efficiency, but it needs more busbars and more cooling spaces when device runs.Double number busbar can not reduce the general energy loss, The following illustration can show clearly.
Suppose the temperature of cooling water is below 40℃, The resistivity of busbar is 1.86u-ohm cm when temperature reaches 40℃.
Suppose the ambient temperature is 35℃,The resistivity of busbar is 2.16u-ohm cm whentemperature reaches 85℃.
When using one water cooled busbar, the energy loss is 1.86 x 1^2 = 1.86.
When using two air cooling busbar, the energy loss is 2.16*((1/3)^2 + (2/3)^2) = 1.20, because current-carrying capacity of the two busbars is not distributed as 50/50, but 33/67.
6、Water cooled leads
General speaking, the energy loss of water cooled leads is 0.23%/m.
The energy loss of water cooled leads is much higher than output busbar, so shorten the length of water cooled length as far as possible is very important. Increasing the number of water cooled leads is helpful to reduce the energy loss. However, normally too many water cooled leads is not practical when furnace is tilted.
7、Electric furnace
The electric furnace is the biggest part of energy loss, but energy saving can be achieved by the following means.
Using good, clean lining.
Organized the structure of lining well, improve the efficiency of efficiency.
Form good habit of covering the lid.
Maintain the lining well, avoid crosslink, when the lining is too thin, stop to use it.
7.1 Electrical loss
The electrical loss of induction coil depends on the shape of coil, resistivity and frequency of metal, when the proportion of effective coil’s diameter and height is 1:1,inside diameter of the melting bath is (0.75-0.8) of inside diameter of coil, and the device runs at 200-300Hz, the electrical loss of coil is :
Coil electrical loss: about 18%.
The loss of shunts and short-circuit ring:about 1.5%.
Loss in total:19.5%
Calculations above is based on the sectional area of coil copper tube is rectangle, coil duty ratio is more than 0.8, and the height of rectangle tube coil is higher 3% than circle tube coil.
7.2 Heat loss
Heat loss is mainly depends on heat conductivity coefficient of lining material, but for iron casting application case, we usually choose quartz sand lining.
Furnace with lid, and its power density is 500kW/ton, heat loss is in the range of 10.6% - 2.3% when the weight of melting iron is from 1ton to 25ton.
Furnace with lid, and its power density is 750kW/ton, heat loss is in the range of 7.1% - 1.5%
Furnace without lid, and its power density is 500kW/ton, heat loss is in the range of 24.2% - 6.9 % when the weight of melting iron is from 1ton to 25ton.
Furnace without lid, and its power density is 750kW/ton, heat loss is in the range of 16.1 % - 4.6 %
We can see clearly that design with high power density and lid can improve the efficiency by the comparison above,it has a abvious advantage when whole melting iron heating or holding.
7.3 Comprehensive consideration of electrical and heat loss
We can see heat and electrical loss of medium furnace has an interesting influence on total loss by comparison of the table below.

The curve below shows something about lining tamping, increasing the thickness of lining improves the life of lining, However, it also reduces the efficiency of electrical furnace. Reducing the thickness of lining to improve the efficiency of the furnace results in shorter life time of lining. Experience before told us that it is time to change lining when current thickness of lining is 2/3 of design thickness. For small furnace, inside diameter of combustion chamber is from 0.75 to 0.83 of coil’s can ensure the best efficiency range, For big furnace, the coefficient should be range from 0.8 to 0.87.
Other energy loss of auxiliary device
There are several sets of configured auxiliary system, including,
——cooling system
——hydraulic system
——dust-removal system
Water cooling system works continuously when electrical furnace is running. After the furnace is off, Cooling system won’t stop running until furnace cools down completely.
Normally for different system, there are different cooling system form, such as open-loop cooling system, closed-loop cooling system, evaporative cooling tower, dry cooling tower, water saving cooling system. While the most common form is closed-loop cooling tower system, which is consist of water pump, spray pump of cooling tower, fans of cooling tower. Since the flow rate is proportional to the power of medium frequency induction furnace, and water pump’s power is proportional to the rate of flow.we can think water pump’s power is proportional to medium frequency furnace’s.
Heat-sinking capability of cooling system is proportional to the power of furnace, so the power needed when cooling tower runs is also proportional to furnace’s power. Here is a relationship about power of water pump, cooling tower on and electrical furnace.
So in system with “one power supply and one furnace”, the energy loss rate is 1.2% of whole medium frequency induction furnace system.
The following are some means to reduce energy loss:
Ensure the temperature switch controlled by cooling tower fan works well,and the setting value is not too low.
Ensure outer circulating water is clean.
Ensure spray tube of cooling tower free,coil pipe of the cooling tower clean,to keep high cooling efficiency.
Ensure spray pump is turned on earlier and turned off later than cooling tower fan, avoid the coil pipe of cooling tower scaling.
Hydraulic system
The size of hydraulic pump of the hydraulic system has a direct relationship with the size of medium frequency furnace. The size of hydraulic pump is about three times of furnace’s ton to ensure two minutes’tilting time, For example, for 10 tons furnace, the power of the hydraulic pump is 30kW in hydraulic system.
Suppose the running time of hydraulic pump is 10 minutes per hour, the power density of the furnace is 500kW/ton, energy loss for the hydraulic system is 0.1% of the whole system, which is very small compared to system’s loss. But remember to turn off hydraulic system in time when it is not needed.
Furnace fume device
Since fume device has a demand for air volume, the fan power of fume device depends on the furnace’s tons, the type of furnace lid, and the melting material. For instance, the fan power of fume hood is twice of the fume ring’s. General speaking, fan’s power is proportional to the cube root of furnace’s tons.
Based on the calculation of fume ring,the energy loss of fume system is in a range like this:the energy loss of 1ton furnace fume system is 0.4% of the system. while for 25 ton furnace, the fume system is 0.14% of the whole melting system. To the melting system with one power supply and one furnace,we have not much energy saving work to do, but to multiple furnaces melting system and when the furnace doesn’t need a fume device, there should be a switching device.

"Excuse me," Arthur ventured, huskily, "did you wish to speak to me?" "What!" Balmayne cried, "were you mad enough to----." seventeen Christmas presents? I'm a Socialist, please remember; And to close the procession came more soldiers. For that fog the seaplane was making at full speed. It was no wonder that Spain, feeling the serious effects of this state of things, should resist it; and when she did so, and exerted an unusual degree of vigilance, then the most terrible outcries were raised, and wonderful stories were circulated of Spanish cruelties to our people beyond the Atlantic. At this time the Opposition got hold of one of these, and made the House of Commons and the nation resound with it. It was, that one Captain Robert Jenkins, who had been master of a sloop trading from Jamaica, had been boarded and searched by a Coastguard, and treated in a most barbarous manner, though they could detect no proof of smuggling in his vessel. He said that the Spanish captain had cut off one of his ears, bidding him carry it to his king, and tell his Majesty that if he were present he would treat him in the same manner. This story was now seven years old, but it was not the less warmly received on that account. It excited the utmost horror, and Jenkins was ordered to appear at the bar of the House of Commons on the 16th of March, to give an account of the outrage himself; and it would appear that both he and other witnesses were examined the same day. Jenkins carried his ear about with him wrapped in cotton, to show to those to whom he related the fact, and the indignation was intense. He was asked by a member how he felt when he found himself in the hands of such barbarians, and he replied, "I recommended my soul to God, and my cause to my country." The worthy skipper had probably been crammed with this dramatic sentiment by some of his clever Parliamentary introducers; but its effect was all the same as if it had been a genuine and involuntary expression of his own mind. Researches made at the Admiralty in 1889 proved that he really had lost an ear. Nevertheless, the whole army was dead beat and in the most deplorable condition when they entered Carlisle on the morning of the 19th. As the enemy did not appear, they rested that day and the following night, when they set forward again, leaving a fresh garrison. Cumberland was soon up before the walls, and they fired vigorously at him; but he sent off to Whitehaven and brought up six eighteen-pounders, with which, to their dismay, he began to play on their crumbling walls on the 29th. Next morning they hung out a white flag, and offered to capitulate; but Cumberland would hear of no terms except their surrendering on condition that they should not be put to the sword. At three o'clock in the afternoon both town and castle were surrendered, the garrison being shut up in the cathedral, and a guard set upon them. On the 3rd of January the Duke of Cumberland left the command to General Hawley, and hastened back to London, being summoned to defend the southern coast from a menaced landing of the French. In pursuance of this plan of the campaign, Prideaux and Johnson arrived before the fort of Niagara in the middle of July, which they found very strong, and garrisoned by six hundred men. Prideaux was soon killed by the bursting of a shell, but Johnson continued the siege with great ability, having to invest the fort on one hand, whilst he was menaced on the other by a mixed body of French and Indians, one thousand seven hundred in number, who came to relieve the fort. The attack upon him commenced with a terrible war-whoop of the Indians, which, mingling with the roar of the great cataract near, made the most horrible din imaginable. But this did not disconcert the English and their savage allies, who received them with such steady courage, that in less than an hour they were put to the rout in sight of their own garrison, and pursued for five miles with dreadful slaughter. The garrison thereupon capitulated, remaining prisoners of war. There, however, Sir William Johnson's career stopped. From various causes, not foreseen, he was not able to advance beyond the Ontario to unite with Amherst. That general had fully succeeded in taking Ticonderoga and Crown Point, but he found the French so strongly posted on an island at the upper end of Lake Champlain, that he was compelled to stop and build[134] boats to enable his army to reach and dislodge them; and it was not till October that he was ready to proceed, when he was driven back repeatedly by tempests, and compelled to go into winter quarters. "Some of you find Lieut. Bowersox, and bring him here," said Capt. McGillicuddy, sitting up, and beginning to twist a handkerchief around his thigh, to form a tourniquet. "Lieutenant, you all right?" The old man mounted into the seat, gathered up the rope lines, and chirruped to the horse to start. He hitched forward cautiously a little farther, to where he could peer through the bushes, being exceedingly wary not to repeat his opponent's mistake, and set their tops in motion. A rock protruding through the ground in front of him made an opening through which he could see, and also afforded a rest for his musket. He looked sharply, and at length was rewarded by seeing the gun-barrel come out by the side of the barked willow, rested on a bare limb, and apparently aimed at the hill beyond. He took a long breath to steady his nerves, stretched out his legs to make himself more at ease, pushed his musket forward until he got exactly the right poise, aimed about nine inches below the level of his opponent's gun-barrel, and a little to the left, drew his bead down to a hair's nicety in the hind sight, and pulled the trigger just as the rebel sharpshooter did the same. Both muskets seemed to flash at the same moment. The rebel sprang up through the willows and fell forward on his face. There was a vague hint that he had seen the face somewhere, but he dismissed it, then settled himself, and, busy with his own thoughts, pressed his face against the window, and tried to recognize through the darkness the objects by which they were rushing. They were all deeply interesting to him, for they were part of Maria's home and surroundings. After awhile the man appeared temporarily tired of billing and cooing, and thought conversation with some one else would give variety to the trip. He opened their lunch-basket, took out something for himself and his companion to eat, nudged Shorty, and offered him a generous handful. Shorty promptly accepted, for he had the perennial hunger of convalescence, and his supper had been interrupted. It was their regiment—the 200th Ind.; it was made up of the same companies, with the great majority of the men the same, but it was very far from being the 200th Ind. which crossed the Ohio River in September, 1862. "I should say he had a mighty strong breath, Monty," Shorty interrupted. He liked to break in on Monty's heroics. "Excuse me from havin' a 12pounder breathin' around me." "Yes, but d?an't m?ake him angry—he might beat you." "I used to be in the fancy," said the minister, "but five years ago the Lord challenged me, and knocked me out in the first round." "We shall talk further," said Holgrave: "in the mean time, we must consult for your own safety. If your father was a villein of this barony, it is not likely that the old steward, or the new one—the fiend Calverley—should forget you; and——"
HoME手机看黄片用什么软件ENTER NUMBET 004
hfgy118.com.cn
yiyou999.com.cn
www.hnqizw.com.cn
www.hyyd.net.cn
lcbxg.com.cn
bqbd.org.cn
www.smbc-card.org.cn
www.leetn.com.cn
hryf.com.cn
oasspuedu.cn